Remediation of metal ions in aqueous solution using activated carbon from Zea may stem
- Authors: Matandabuzo, Mzukisi
- Date: 2016
- Language: English
- Type: Thesis , Masters , MSc (Chemistry)
- Identifier: vital:11360 , http://hdl.handle.net/10353/d1021328
- Description: Zea mays stem and its activated carbon were prepared through chemical activation method using four different activating reagents (NaOH, H₃PO₄, H₂SO₄, KOH) and were used as adsorbents for the removal of Pb(II), Cu(II), Hg(II) and Cr(III) from aqueous solution. The results shows that activated carbon has high surface area and pore volume compared to the powdered raw Zea mays stem. Prepared activated carbon was characterized using physico-chemical properties such as carbon yield, iodine number, moisture content, percentage adsorption, and analytical instruments such as Fourier transform Infrared spectroscopy (FTIR), atomic absorption spectrometer (AAS), scanning electron microscopy (SEM), Energy Dispersive X-ray analysis (EDS), powder X-ray Diffraction (pXRD). The adsorption of Pb(II), Cu(II), and Cr(III) ions were pH, contact time, and concentration dependent. Based on the results obtained from the batch experiments, activated carbon prepared from Zea mays stem is not good enough for the removal of Hg(II) from aqueous solution. Adsorption ability was calculated and found to be 66.67% for activated carbon obtained from H₂SO₄, 21.21% for activated carbon obtained from KOH, and 20% for activated carbons obtained from NaOH and H₃PO₄. The pH 5-6 was chosen for all experiments, contact time was 2 hours, and adsorbent dosage was 2 g, initial concentration range from 200, 400, 600, 800, and 1000 ppm at room temperature. The metal ion removal trend was found in the order Pb(II)>Cu(II)>Cr(III)>>Hg(II). The Langmuir model fitted well in most of the cases with > 0.99. Consequently, the adsorption of Pb(II) and Cu(II) followed Langmuir isotherm model while that of Cr(III) best fitted the Freundlich isotherm model. The results indicated that the adsorption process followed two possible mechanisms. (I) Metal ion – adsorbent complex model and (II) Metal ion – ion-exchange adsorbent complex model.
- Full Text:
- Date Issued: 2016
- Authors: Matandabuzo, Mzukisi
- Date: 2016
- Language: English
- Type: Thesis , Masters , MSc (Chemistry)
- Identifier: vital:11360 , http://hdl.handle.net/10353/d1021328
- Description: Zea mays stem and its activated carbon were prepared through chemical activation method using four different activating reagents (NaOH, H₃PO₄, H₂SO₄, KOH) and were used as adsorbents for the removal of Pb(II), Cu(II), Hg(II) and Cr(III) from aqueous solution. The results shows that activated carbon has high surface area and pore volume compared to the powdered raw Zea mays stem. Prepared activated carbon was characterized using physico-chemical properties such as carbon yield, iodine number, moisture content, percentage adsorption, and analytical instruments such as Fourier transform Infrared spectroscopy (FTIR), atomic absorption spectrometer (AAS), scanning electron microscopy (SEM), Energy Dispersive X-ray analysis (EDS), powder X-ray Diffraction (pXRD). The adsorption of Pb(II), Cu(II), and Cr(III) ions were pH, contact time, and concentration dependent. Based on the results obtained from the batch experiments, activated carbon prepared from Zea mays stem is not good enough for the removal of Hg(II) from aqueous solution. Adsorption ability was calculated and found to be 66.67% for activated carbon obtained from H₂SO₄, 21.21% for activated carbon obtained from KOH, and 20% for activated carbons obtained from NaOH and H₃PO₄. The pH 5-6 was chosen for all experiments, contact time was 2 hours, and adsorbent dosage was 2 g, initial concentration range from 200, 400, 600, 800, and 1000 ppm at room temperature. The metal ion removal trend was found in the order Pb(II)>Cu(II)>Cr(III)>>Hg(II). The Langmuir model fitted well in most of the cases with > 0.99. Consequently, the adsorption of Pb(II) and Cu(II) followed Langmuir isotherm model while that of Cr(III) best fitted the Freundlich isotherm model. The results indicated that the adsorption process followed two possible mechanisms. (I) Metal ion – adsorbent complex model and (II) Metal ion – ion-exchange adsorbent complex model.
- Full Text:
- Date Issued: 2016
Synthesis and structural studies of NiS and PdS nanoparticles/nanocomposites from dithiocarbamates single source precursors
- Authors: Nqombolo, Azile
- Date: 2016
- Language: English
- Type: Thesis , Masters , MSc (Chemistry)
- Identifier: vital:11359 , http://hdl.handle.net/10353/d1021326
- Description: The main aim of this research is to synthesize Ni(II) and Pd(II) dithiocarbamate complexes and use them as single source precursors for the synthesis of NiS and PdS nanoparticles and metal sulphides potato starch nanocomposites. Four dithiocarbamate ligands were synthesized and characterized using elemental analysis and spectroscopic techniques. The ligands were used to prepared homoleptic Ni(II) and Pd(II) complexes of the dithiocarbamate ligands. The metal complexes were characterized with elemental analysis, UV-Vis, FTIR and 1H-NMR spectroscopic techniques. Conductivity measurements indicate that all the complexes are non-electrolytes in solution and results from the electronic spectra studies confirmed the proposed 4-coordinate square planar geometry around the metal ions. The nickel complexes showed d-d transitions around 477 nm while in the palladium complexes, no d-d transitions were observed but the compounds showed strong metal to ligand charge transfer transitions. From the FTIR spectra studies, it can be confirmed that the complexes were successfully synthesised because all peaks of interest were observed at expected regions from the literature. The νC-N was observed around 1469-1495 cm-1, νC=S around 1101-1188 cm-1 and νC-S around 738-1060 cm-1 for both Ni(II) and Pd(II) complexes. νNi-S was observed around 375-543 cm-1 and νPd-S around 529-545 cm-1. The FTIR also confirmed that the dithiocarbamate ligands act as bidentate chelating ligands through the sulfur atoms. The complexes were used as single source precursors and thermolysed in hexadecylamine (HDA) at 220 °C to prepare four HDA-capped nickel sulfide nanoparticles and four palladium sulfide nanoparticles. The as-prepared nanoparticles were studied with optical absorption spectra, photoluminescence, powder X-ray diffraction (PXRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). The optical studies results showed that NiS have large band gaps that are greater than that of the bulk, therefore they are found to be blue shifted relative to the bulk, which shows that they have small particle size and thus confirming their quantum confinement effect. PL spectra reveal that the emission peaks are red shifted compared to the absorption band edges of the nanoparticles. The XRD patterns confirmed the formation of cubic and rhombohedral phase for NiS nanoparticles and cubic phase for PdS nanoparticles. SEM images of both NiS and PdS show uniform surface morphology at low and high magnification with different shapes. EDS analyses confirmed the presence of Ni, S, and Pd in each of the spectrum indicating that the nanoparticles were successfully synthesized. TEM images showed that the synthesised nanoparticles have uniform and narrow size distribution with no agglomeration. The sizes of the NiS nanoparticles were found to be in the range of 12-38 nm for NiS1, 8-11 nm for NiS2, 9-16 nm for NiS3 and 4-9 nm for NiS4. The TEM images for the as-prepared PdS nanoparticles showed that the average crystallite sizes are 6.94-9.62 nm for PdS1, 8-11 nm for PdS2, 9-16 nm for PdS3 and 4-9 nm for PdS4 respectively. The nanoparticles were used to prepare potato starch nanocomposites and SEM images indicate that the surface morphology of starch polymer nanocomposites compose of potato starch and few particles in between the pores of the matrix, this is due to the small ratio of nanoparticles used.
- Full Text:
- Date Issued: 2016
- Authors: Nqombolo, Azile
- Date: 2016
- Language: English
- Type: Thesis , Masters , MSc (Chemistry)
- Identifier: vital:11359 , http://hdl.handle.net/10353/d1021326
- Description: The main aim of this research is to synthesize Ni(II) and Pd(II) dithiocarbamate complexes and use them as single source precursors for the synthesis of NiS and PdS nanoparticles and metal sulphides potato starch nanocomposites. Four dithiocarbamate ligands were synthesized and characterized using elemental analysis and spectroscopic techniques. The ligands were used to prepared homoleptic Ni(II) and Pd(II) complexes of the dithiocarbamate ligands. The metal complexes were characterized with elemental analysis, UV-Vis, FTIR and 1H-NMR spectroscopic techniques. Conductivity measurements indicate that all the complexes are non-electrolytes in solution and results from the electronic spectra studies confirmed the proposed 4-coordinate square planar geometry around the metal ions. The nickel complexes showed d-d transitions around 477 nm while in the palladium complexes, no d-d transitions were observed but the compounds showed strong metal to ligand charge transfer transitions. From the FTIR spectra studies, it can be confirmed that the complexes were successfully synthesised because all peaks of interest were observed at expected regions from the literature. The νC-N was observed around 1469-1495 cm-1, νC=S around 1101-1188 cm-1 and νC-S around 738-1060 cm-1 for both Ni(II) and Pd(II) complexes. νNi-S was observed around 375-543 cm-1 and νPd-S around 529-545 cm-1. The FTIR also confirmed that the dithiocarbamate ligands act as bidentate chelating ligands through the sulfur atoms. The complexes were used as single source precursors and thermolysed in hexadecylamine (HDA) at 220 °C to prepare four HDA-capped nickel sulfide nanoparticles and four palladium sulfide nanoparticles. The as-prepared nanoparticles were studied with optical absorption spectra, photoluminescence, powder X-ray diffraction (PXRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). The optical studies results showed that NiS have large band gaps that are greater than that of the bulk, therefore they are found to be blue shifted relative to the bulk, which shows that they have small particle size and thus confirming their quantum confinement effect. PL spectra reveal that the emission peaks are red shifted compared to the absorption band edges of the nanoparticles. The XRD patterns confirmed the formation of cubic and rhombohedral phase for NiS nanoparticles and cubic phase for PdS nanoparticles. SEM images of both NiS and PdS show uniform surface morphology at low and high magnification with different shapes. EDS analyses confirmed the presence of Ni, S, and Pd in each of the spectrum indicating that the nanoparticles were successfully synthesized. TEM images showed that the synthesised nanoparticles have uniform and narrow size distribution with no agglomeration. The sizes of the NiS nanoparticles were found to be in the range of 12-38 nm for NiS1, 8-11 nm for NiS2, 9-16 nm for NiS3 and 4-9 nm for NiS4. The TEM images for the as-prepared PdS nanoparticles showed that the average crystallite sizes are 6.94-9.62 nm for PdS1, 8-11 nm for PdS2, 9-16 nm for PdS3 and 4-9 nm for PdS4 respectively. The nanoparticles were used to prepare potato starch nanocomposites and SEM images indicate that the surface morphology of starch polymer nanocomposites compose of potato starch and few particles in between the pores of the matrix, this is due to the small ratio of nanoparticles used.
- Full Text:
- Date Issued: 2016
Ni(II) and Pb(II) dithiocarbamate complexes as precursors for the synthesis of HDA-capped NiS and PbS nanoparticles
- Authors: Chintso, Thobani
- Date: 2015
- Language: English
- Type: Thesis , Masters , MSc (Chemistry)
- Identifier: vital:11349 , http://hdl.handle.net/10353/d1020201
- Description: Ni(II) and Pb(II) dithiocarbamate complexes were synthesized and characterized by elemental analysis, UV-Vis, FTIR and TGA and some of the Ni(II) complexes and one Pb(II) were further analyzed by 1H-NMR and 13C-NMR spectroscopy. Generally all the dithiocarbamate ligands are soluble in water while the complexes were soluble mostly in solvents such as chloroform, toluene, DMSO and DCM. Based on the elemental analysis, the dithiocarbamate complexes are formulated as four coordinate (tetrahedral or square planar) compounds. However, the FTIR showed that each of the dithiocarbamate ligands acted as bidentate ligand through two sulfur atoms. The TGA of the most complexes showed one major decomposition step to give respective metal sulfide above 200 oC. In this research project, dithiocarbamate complexes were used as single source precursor for the synthesis of metal sulfide nanoparticles. We studied the optical and structural properties of metal sulfide nanoparticles using UV-Vis, photoluminescence (PL), powder X-ray diffraction (XRD), energy dispersive X-ray (EDX), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The absorption spectra of the metal sulfide nanoparticles are blue shifted in respect to bulk material and they also showed broad emission. The XRD of the NiS nanoparticles were indexed to the cubic and rhombohedral phase, with crystallite sizes of 15 - 18 nm. The XRD of PbS nanoparticles were indexed to the face centered cubic and cubic rock salts, with the crystallite sizes 12 - 18 nm. The TEM images of the metal sulfide nanoparticles showed particles with spherical and rectangular shapes with crystallite sizes 4 - 35 nm.
- Full Text:
- Date Issued: 2015
- Authors: Chintso, Thobani
- Date: 2015
- Language: English
- Type: Thesis , Masters , MSc (Chemistry)
- Identifier: vital:11349 , http://hdl.handle.net/10353/d1020201
- Description: Ni(II) and Pb(II) dithiocarbamate complexes were synthesized and characterized by elemental analysis, UV-Vis, FTIR and TGA and some of the Ni(II) complexes and one Pb(II) were further analyzed by 1H-NMR and 13C-NMR spectroscopy. Generally all the dithiocarbamate ligands are soluble in water while the complexes were soluble mostly in solvents such as chloroform, toluene, DMSO and DCM. Based on the elemental analysis, the dithiocarbamate complexes are formulated as four coordinate (tetrahedral or square planar) compounds. However, the FTIR showed that each of the dithiocarbamate ligands acted as bidentate ligand through two sulfur atoms. The TGA of the most complexes showed one major decomposition step to give respective metal sulfide above 200 oC. In this research project, dithiocarbamate complexes were used as single source precursor for the synthesis of metal sulfide nanoparticles. We studied the optical and structural properties of metal sulfide nanoparticles using UV-Vis, photoluminescence (PL), powder X-ray diffraction (XRD), energy dispersive X-ray (EDX), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The absorption spectra of the metal sulfide nanoparticles are blue shifted in respect to bulk material and they also showed broad emission. The XRD of the NiS nanoparticles were indexed to the cubic and rhombohedral phase, with crystallite sizes of 15 - 18 nm. The XRD of PbS nanoparticles were indexed to the face centered cubic and cubic rock salts, with the crystallite sizes 12 - 18 nm. The TEM images of the metal sulfide nanoparticles showed particles with spherical and rectangular shapes with crystallite sizes 4 - 35 nm.
- Full Text:
- Date Issued: 2015
Synthesis and characterization of Ru(II) phenyl-3-indenylidene olefin metathesis type complexes
- Authors: Yalezo, Ntsikelelo
- Date: 2015
- Language: English
- Type: Thesis , Masters , MSc (Chemistry)
- Identifier: vital:11351 , http://hdl.handle.net/10353/d1021128
- Description: In this study, a series of Ru(II) phenyl-3-indenylidene complexes with general formula of [RuCl2(NHC)(Ind)(L)] (where L= triphenylphosphine, pyridine and NHC = five different types of N-heterocyclic carbene ligands), have been synthesized and characterized using FT-IR, UV-Vis, elementally analysis and melting/decomposition point. The N,N’-diarylimidazolinium chlorides have been used as N-heterocyclic carbene precursors and were synthesized from their corresponding N,N’-diarylformamidines and further characterized using 1H-NMR, 13C-NMR, FTIR and melting point determination. The infrared spectra of the N,N’-diarylimidazolinium chlorides show a quaternary nature (R2N=C+) with broad vibration band in region 3300-3400 cm-1. The disappearance of this vibration band in the infrared spectra of the ruthenium(II) complexes was used to confirm the coordination of the ligand to the ruthenium ions. The percentage analysis of carbon, hydrogen and nitrogen obtained corresponded with the calculated percentages of these atoms in the complexes with the slight difference of less than 1%. The electronic spectra of the complexes show three distinct absorption bands. The two bands are due to intraligand charge transfers transition assigned to π→π*, n→π* and third band is due to d-d transition, signifying the presence of the metal ion. The synthesized Ru(II) complexes did not show any of melting, however a change in colour was observed signifying the decomposition of the complexes.
- Full Text:
- Date Issued: 2015
- Authors: Yalezo, Ntsikelelo
- Date: 2015
- Language: English
- Type: Thesis , Masters , MSc (Chemistry)
- Identifier: vital:11351 , http://hdl.handle.net/10353/d1021128
- Description: In this study, a series of Ru(II) phenyl-3-indenylidene complexes with general formula of [RuCl2(NHC)(Ind)(L)] (where L= triphenylphosphine, pyridine and NHC = five different types of N-heterocyclic carbene ligands), have been synthesized and characterized using FT-IR, UV-Vis, elementally analysis and melting/decomposition point. The N,N’-diarylimidazolinium chlorides have been used as N-heterocyclic carbene precursors and were synthesized from their corresponding N,N’-diarylformamidines and further characterized using 1H-NMR, 13C-NMR, FTIR and melting point determination. The infrared spectra of the N,N’-diarylimidazolinium chlorides show a quaternary nature (R2N=C+) with broad vibration band in region 3300-3400 cm-1. The disappearance of this vibration band in the infrared spectra of the ruthenium(II) complexes was used to confirm the coordination of the ligand to the ruthenium ions. The percentage analysis of carbon, hydrogen and nitrogen obtained corresponded with the calculated percentages of these atoms in the complexes with the slight difference of less than 1%. The electronic spectra of the complexes show three distinct absorption bands. The two bands are due to intraligand charge transfers transition assigned to π→π*, n→π* and third band is due to d-d transition, signifying the presence of the metal ion. The synthesized Ru(II) complexes did not show any of melting, however a change in colour was observed signifying the decomposition of the complexes.
- Full Text:
- Date Issued: 2015
Computational studies, synthesis and characterization of ruthenium (ii) anticancer complexes
- Authors: Adeniyi, Adebayo Azeez
- Date: 2014
- Language: English
- Type: Thesis , Doctoral , PhD (Chemistry)
- Identifier: vital:11338 , http://hdl.handle.net/10353/d1015577
- Description: This thesis is centred on the application of Ru-based complexes as a promising alternative to cis-platin in cancer chemotherapy. Cis-platin is known to be the most prescribed chemotherapy which has more than 70% application in cancer cases especially the testicular cancer. An insight is provided in Chapter One and Two into the literatures reports on the application of Ru(II)-based complexes in cancer chemotherapy. In order to address some of the pressing challenges in rational design of Ru-based anticancer complexes, section 3.3 and 3.4 deal with efforts to elucidate the complication of their chemistry and instability while in section 3.5 efforts are made to find solution to the lack of proper knowledge of their targets using different theoretical approaches as presented in Chapter Three. In addition to the theoretical study, this thesis also comprises of the synthesis of the bis-pyrazole derivatives type of ligands and the derivatives of their Ru(II)-based complexes as provided in Chapter Four and Five respectively. Also the computational methods were used to elucidate the structural and spectroscopic properties of the synthesised ligands and their Ru(II)-based complexes. The geometrical and electronic properties are studied in relation to the stability and the reported anticancer activities of Ru(II)-based complexes in section 3.3. In subsection 3.3.1, several quantum properties including the natural energy decomposition analysis (NEDA) and quantum theory of atoms in a molecule (QTAIM) are computed on three models of RAPTA-C complexes using DFT with hybrid functional and basis set with ECP and without ECP. The higher stability of Carbo-RAPTA-C and Oxalo-RAPTA-C over RAPTA-C comes from the lower exchange repulsion and higher polarization contributions to their stability which gives insight into experimental observation. A similar study was carried out in subsection 3.3.2 on half-sandwich Ru(II)-based anticancer complexes with 6-toluene and 6-trifluorotoluene.
- Full Text:
- Date Issued: 2014
- Authors: Adeniyi, Adebayo Azeez
- Date: 2014
- Language: English
- Type: Thesis , Doctoral , PhD (Chemistry)
- Identifier: vital:11338 , http://hdl.handle.net/10353/d1015577
- Description: This thesis is centred on the application of Ru-based complexes as a promising alternative to cis-platin in cancer chemotherapy. Cis-platin is known to be the most prescribed chemotherapy which has more than 70% application in cancer cases especially the testicular cancer. An insight is provided in Chapter One and Two into the literatures reports on the application of Ru(II)-based complexes in cancer chemotherapy. In order to address some of the pressing challenges in rational design of Ru-based anticancer complexes, section 3.3 and 3.4 deal with efforts to elucidate the complication of their chemistry and instability while in section 3.5 efforts are made to find solution to the lack of proper knowledge of their targets using different theoretical approaches as presented in Chapter Three. In addition to the theoretical study, this thesis also comprises of the synthesis of the bis-pyrazole derivatives type of ligands and the derivatives of their Ru(II)-based complexes as provided in Chapter Four and Five respectively. Also the computational methods were used to elucidate the structural and spectroscopic properties of the synthesised ligands and their Ru(II)-based complexes. The geometrical and electronic properties are studied in relation to the stability and the reported anticancer activities of Ru(II)-based complexes in section 3.3. In subsection 3.3.1, several quantum properties including the natural energy decomposition analysis (NEDA) and quantum theory of atoms in a molecule (QTAIM) are computed on three models of RAPTA-C complexes using DFT with hybrid functional and basis set with ECP and without ECP. The higher stability of Carbo-RAPTA-C and Oxalo-RAPTA-C over RAPTA-C comes from the lower exchange repulsion and higher polarization contributions to their stability which gives insight into experimental observation. A similar study was carried out in subsection 3.3.2 on half-sandwich Ru(II)-based anticancer complexes with 6-toluene and 6-trifluorotoluene.
- Full Text:
- Date Issued: 2014
Structural, optical and electrical characterization of nano-sized c-tio2 quamtum dots synthesized by spray pyrolysis
- Authors: Taziwa, Raymond Tichaona
- Date: 2014
- Language: English
- Type: Thesis , Doctoral , PhD (Chemistry)
- Identifier: vital:11342 , http://hdl.handle.net/10353/d1016089
- Description: In the 21st century, scientific communities face challenges and opportunities concerning future development, where innovations must be a key driver over the past, evolution of African societies were based on incomplete models, only taking into account economical growth and not paying attention to environmental deterioration as a consequence of anthropogenic activity and environmental pollution. We have to learn from our past mistakes in order not to repeat them. Education and research of today as the embryonic stages of the development models of tomorrow should be directed toward a sustainable mentality. In this sense, solar energy technologies have emerged as key instruments for minimizing environmental impact as well as reducing economic cost in the field of renewable energies. Titanium dioxide is a fascinating low cost material exhibiting unique properties of stability and photo catalytic activities, leading to clean technologies in water purification and energy conversion of sunlight. However, conventional techniques (high temperature, high vacuum, high pressures) of processing titanium dioxide are a technological limitation due to excessive energy consumption. This poses a handicap for practical applications in areas such as preparation of hybrid organic/Titanium dioxide materials or devices on thermo flexible substrates such as plastic material. It is for this reason that the investigation presented in this Ph.D thesis deals with the development of spray pyrolysis techniques for preparation of carbon doped titanium dioxide nano powders for solar cell applications. This thesis is therefore structured as follows: Chapter 1 gives a general overview of the work done in this thesis. This work relies greatly on the excellent structural optical and electrical properties of TiO2 thin films, as well as its chemical resistance and insulating properties. A summary of the physical, optical, electrical and chemical properties reported in the literature, with an emphasis on those relevant to solar cell fabrication, is presented in Chapter 2. Chapter 3 gives a concise literature review on models governing droplet formation in ultrasonic spray pyrolysis (USP) techniques, the limitations of these models have been exposed and a new relation model for estimating the final particle size given a set of initial reaction conditions has been proposed. The presently derived model is quite advantageous in that it does not require the investigator to look up values of surface tension and density for every precursor solution. Chapter 4 presents in detail the designed and constructed spray pyrolysis system capable of realizing desired nano structures for photovoltaic applications. The first system employed an ultrasonic atomization spray nozzle in order to create an aerosol of the TiO2 precursor. The reasons for choosing ultrasonic spray deposition (USP) and the TiO2 precursors, titanium iso propoxide and titanium tetra butoxide are discussed. Chapter 5 outlines experimental methodologies used in synthesis and characterization of the materials used in this study. Chapter 5 further provides experimental methodologies used in fabrication of a new type of photo electrochemical solar cells (PECs). Chapter 6 reveals the opto-electrical results of PECs solar cells fabricated. There are numerous properties that are affected by the size but emphasis will be placed on nano-size and confinement effects. Chapter 7 presents a confirmation of the phonon confinement effects in C-TiO2 QDs for the first time. In addition Chapter 7 also presents a new phonon confinement model. Chapter 8 reveals the optical, structural and electronic properties of C-TiO2 QDs synthesized by USP and PSP techniques. In addition the electrical properties of C-TiO2 QDs PEC solar cells devices are reported in Chapter 8. Concluding remarks, with potential future research projects are presented in Chapter 9. Through these 9 chapters, all research questions have been answered satisfactorily and all objectives met. Most of the work contained in this thesis has been subjected to external reviews through publication of these peer reviewed articles.
- Full Text:
- Date Issued: 2014
- Authors: Taziwa, Raymond Tichaona
- Date: 2014
- Language: English
- Type: Thesis , Doctoral , PhD (Chemistry)
- Identifier: vital:11342 , http://hdl.handle.net/10353/d1016089
- Description: In the 21st century, scientific communities face challenges and opportunities concerning future development, where innovations must be a key driver over the past, evolution of African societies were based on incomplete models, only taking into account economical growth and not paying attention to environmental deterioration as a consequence of anthropogenic activity and environmental pollution. We have to learn from our past mistakes in order not to repeat them. Education and research of today as the embryonic stages of the development models of tomorrow should be directed toward a sustainable mentality. In this sense, solar energy technologies have emerged as key instruments for minimizing environmental impact as well as reducing economic cost in the field of renewable energies. Titanium dioxide is a fascinating low cost material exhibiting unique properties of stability and photo catalytic activities, leading to clean technologies in water purification and energy conversion of sunlight. However, conventional techniques (high temperature, high vacuum, high pressures) of processing titanium dioxide are a technological limitation due to excessive energy consumption. This poses a handicap for practical applications in areas such as preparation of hybrid organic/Titanium dioxide materials or devices on thermo flexible substrates such as plastic material. It is for this reason that the investigation presented in this Ph.D thesis deals with the development of spray pyrolysis techniques for preparation of carbon doped titanium dioxide nano powders for solar cell applications. This thesis is therefore structured as follows: Chapter 1 gives a general overview of the work done in this thesis. This work relies greatly on the excellent structural optical and electrical properties of TiO2 thin films, as well as its chemical resistance and insulating properties. A summary of the physical, optical, electrical and chemical properties reported in the literature, with an emphasis on those relevant to solar cell fabrication, is presented in Chapter 2. Chapter 3 gives a concise literature review on models governing droplet formation in ultrasonic spray pyrolysis (USP) techniques, the limitations of these models have been exposed and a new relation model for estimating the final particle size given a set of initial reaction conditions has been proposed. The presently derived model is quite advantageous in that it does not require the investigator to look up values of surface tension and density for every precursor solution. Chapter 4 presents in detail the designed and constructed spray pyrolysis system capable of realizing desired nano structures for photovoltaic applications. The first system employed an ultrasonic atomization spray nozzle in order to create an aerosol of the TiO2 precursor. The reasons for choosing ultrasonic spray deposition (USP) and the TiO2 precursors, titanium iso propoxide and titanium tetra butoxide are discussed. Chapter 5 outlines experimental methodologies used in synthesis and characterization of the materials used in this study. Chapter 5 further provides experimental methodologies used in fabrication of a new type of photo electrochemical solar cells (PECs). Chapter 6 reveals the opto-electrical results of PECs solar cells fabricated. There are numerous properties that are affected by the size but emphasis will be placed on nano-size and confinement effects. Chapter 7 presents a confirmation of the phonon confinement effects in C-TiO2 QDs for the first time. In addition Chapter 7 also presents a new phonon confinement model. Chapter 8 reveals the optical, structural and electronic properties of C-TiO2 QDs synthesized by USP and PSP techniques. In addition the electrical properties of C-TiO2 QDs PEC solar cells devices are reported in Chapter 8. Concluding remarks, with potential future research projects are presented in Chapter 9. Through these 9 chapters, all research questions have been answered satisfactorily and all objectives met. Most of the work contained in this thesis has been subjected to external reviews through publication of these peer reviewed articles.
- Full Text:
- Date Issued: 2014
Synthesis and characterization of metal sulfide nanoparticles/polymer nanocomposites
- Authors: Mbese, Johannes Zanoxolo
- Date: 2013
- Language: English
- Type: Thesis , Masters , MSc (Chemistry)
- Identifier: vital:11344 , http://hdl.handle.net/10353/d1016190
- Description: The focus of this project was to synthesize and characterize metal sulfide nanoparticles /polymer nanocomposites. The work involved the synthesis of dithiocarbamato ligands and complexes derived from aniline. Zn(II), Cd(II) and Hg(II) dithiocarbamato complexes were used as single-molecule precursors for the synthesis of the ZnS, CdS and HgS nanoparticles and their optical and structural properties studied. The other focus of this work was to synthesize a combined functionality metal sulfide nanoparticles/polymer nanocomposites by dispersing as-synthesized ZnS, CdS and HgS nanoparticles in polymethyl methacrylate (PMMA) matrix. The characterization of the ligands, complexes, nanoparticles and nanocomposites were investigated using relevant instrumental tools like UV-Vis, photoluminescence (PL), Fourier transform infrared (FTIR), X-ray diffraction (XRD), energy dispersion X-ray (EDX), nuclear magnetic resonance (NMR), scanning electron microscopy (SEM) and transmission electron microscopy (TEM).
- Full Text:
- Date Issued: 2013
- Authors: Mbese, Johannes Zanoxolo
- Date: 2013
- Language: English
- Type: Thesis , Masters , MSc (Chemistry)
- Identifier: vital:11344 , http://hdl.handle.net/10353/d1016190
- Description: The focus of this project was to synthesize and characterize metal sulfide nanoparticles /polymer nanocomposites. The work involved the synthesis of dithiocarbamato ligands and complexes derived from aniline. Zn(II), Cd(II) and Hg(II) dithiocarbamato complexes were used as single-molecule precursors for the synthesis of the ZnS, CdS and HgS nanoparticles and their optical and structural properties studied. The other focus of this work was to synthesize a combined functionality metal sulfide nanoparticles/polymer nanocomposites by dispersing as-synthesized ZnS, CdS and HgS nanoparticles in polymethyl methacrylate (PMMA) matrix. The characterization of the ligands, complexes, nanoparticles and nanocomposites were investigated using relevant instrumental tools like UV-Vis, photoluminescence (PL), Fourier transform infrared (FTIR), X-ray diffraction (XRD), energy dispersion X-ray (EDX), nuclear magnetic resonance (NMR), scanning electron microscopy (SEM) and transmission electron microscopy (TEM).
- Full Text:
- Date Issued: 2013
The characterization and electrochemistry of dye-sensitized solar cells
- Authors: Caga, Noloyiso
- Date: 2013
- Subjects: Dye-sensitized solar cells , Acetonitrile , Electrochemistry , Spectrum analysis
- Language: English
- Type: Thesis , Masters , MSc (Chemistry)
- Identifier: vital:11341 , http://hdl.handle.net/10353/d1016069 , Dye-sensitized solar cells , Acetonitrile , Electrochemistry , Spectrum analysis
- Description: In this study a presentation of the technology behind dye-sensitized solar cells, their design as well as the role of the different parts of the cell. The characterization of the cell is divided into four sections namely: the characterization of the paste required to make the TiO2 film and its optical properties using SEM-EDX and XRD analytical techniques; Analysis of the various absorptions of three Ru-based dyes using UV-Vis spectroscopy, Photoluminescence and Fourier Transform Infra-Red spectroscopy; the characterization and the analyses of the entire cell using Electrochemical Impedance Spectroscopy. The nine cells were prepared by examining RuL2(CN)2 , RuL2(NCS)2 or N3 dye and RuL2(NCS)2 TBA+ or N719 dye. [L = 2,2'-bipyridyl-4,4'-dicarboxylic acid ;TBA = tetra-butyl ammonium] were combined with three electrolytes namely: Z–150 , AN–50 and PN–50. The Iodolyte PN–50 is an iodide based low viscosity electrolyte with 50 mM of tri-iodide dissolved in a solvent called propionitrile (PN). The Iodolyte AN–50 is an iodide based low viscosity electrolyte with 50 mM of tri-iodide dissolved in a solvent called acetonitrile (AN). The Iodolyte Z–150 is an iodide based low viscosity electrolyte with 150 mM of tri-iodide dissolved in a solvent called 3-methoxypropionitrile (MPN) and with additives such an ionic liquid, malkylbenziimidazole and guanidine thiocyanate. A solar simulator was utilized with which the standard solar irradiation can be created in laboratory conditions. The fill factors as well as overall performance efficiencies of the these cells are quite low < 1.0%,.
- Full Text:
- Date Issued: 2013
- Authors: Caga, Noloyiso
- Date: 2013
- Subjects: Dye-sensitized solar cells , Acetonitrile , Electrochemistry , Spectrum analysis
- Language: English
- Type: Thesis , Masters , MSc (Chemistry)
- Identifier: vital:11341 , http://hdl.handle.net/10353/d1016069 , Dye-sensitized solar cells , Acetonitrile , Electrochemistry , Spectrum analysis
- Description: In this study a presentation of the technology behind dye-sensitized solar cells, their design as well as the role of the different parts of the cell. The characterization of the cell is divided into four sections namely: the characterization of the paste required to make the TiO2 film and its optical properties using SEM-EDX and XRD analytical techniques; Analysis of the various absorptions of three Ru-based dyes using UV-Vis spectroscopy, Photoluminescence and Fourier Transform Infra-Red spectroscopy; the characterization and the analyses of the entire cell using Electrochemical Impedance Spectroscopy. The nine cells were prepared by examining RuL2(CN)2 , RuL2(NCS)2 or N3 dye and RuL2(NCS)2 TBA+ or N719 dye. [L = 2,2'-bipyridyl-4,4'-dicarboxylic acid ;TBA = tetra-butyl ammonium] were combined with three electrolytes namely: Z–150 , AN–50 and PN–50. The Iodolyte PN–50 is an iodide based low viscosity electrolyte with 50 mM of tri-iodide dissolved in a solvent called propionitrile (PN). The Iodolyte AN–50 is an iodide based low viscosity electrolyte with 50 mM of tri-iodide dissolved in a solvent called acetonitrile (AN). The Iodolyte Z–150 is an iodide based low viscosity electrolyte with 150 mM of tri-iodide dissolved in a solvent called 3-methoxypropionitrile (MPN) and with additives such an ionic liquid, malkylbenziimidazole and guanidine thiocyanate. A solar simulator was utilized with which the standard solar irradiation can be created in laboratory conditions. The fill factors as well as overall performance efficiencies of the these cells are quite low < 1.0%,.
- Full Text:
- Date Issued: 2013
- «
- ‹
- 1
- ›
- »